MSO2116B

Model	Channels	Sample Rate	Memory	Bus Trigger / Protocol Analyzer	Power Sequence Channels
MSO2008E	8	2GHz	2Gb	I	8
MSO2116E	16	2GHz	4Gb	I, II	16
MSO2116B	16	2GHz	4Gb	I, II, III	16
MSO2216B	16	2GHz	8Gb	I, II, III, IV	16 (128 / 8 sets cascaded)

Datasheet [PDF]

Bus Decode : BiSS-C, CAN 2.0B/CAN FD, DP_Aux, eSPI, I²C, I²S, MIPI I3C, MII, Serial Flash, SPI, SVID, UART (RS232), USB PD 3, USB1.1, ... (100+)

Bus Trigger I : I²C, MIPI I3C 1.1, SPI, UART (RS232)
Bus Trigger II : BiSS-C, CAN2.0B/CAN FD, DP_Aux, HID over I²C, I2S, LIN2.2, MIPI SoundWire 1.2, SENT, USB PD 3
Bus Trigger III : DALI, LPC, MDIO, Mini/Micro LED, MIPI RFFE 3, MIPI SPMI 2.0, Modbus, PMBus, Profibus, SMBus, SVI2, USB1.1
Bus Trigger IV : eMMC 4.5, eSPI, MII, RGMII, RMII, SD 2.0 (SDIO 2.0), Serial Flash (SPI NAND), SVID

Protocol Analyzer I : I²C, MIPI I3C 1.1, SPI, UART (RS232)
Protocol Analyzer II : BiSS-C, CAN2.0B/CAN FD, DP_Aux, HID over I²C, I2S, LIN2.2, USB PD 3
Protocol Analyzer III : DALI, MDIO, MIPI RFFE 3, Modbus, PMBus, Profibus, PWM, SMBus, USB1.1
Protocol Analyzer IV : eSPI, MII, RGMII, RMII, SVID

Logic Analyzer (LA) Mode

• MSO analog and digital channels can capture signals simultaneously.
  It can also stack an oscilloscope to compare digital and analog signals simultaneously, which is suitable for signal quality analysis.

  LA Storage Mode:
  Long Time Record: Transitional Storage VS Compressed Storage
  For signal capture and analysis, usually require to record the signal for a long time. If the data is stored in a compressed way, it will cause your software to lag or even stop functioning when decompressing the data after it is sent back to the computer. Because PC memory size might insufficient for decompressed data size. To satisfy the requirement of smooth software operation and long-term recording without missing any data, the storage method adopted by the Acute analyzer is transitional storage rather than compression. After returning to the PC software, it doesn't need to do the decompression. The decoded results can be displayed while the analysis is finished. 
  
  
  
  Software Main Window
  
  Analog & Digital waveform
  Auto Threshold Settings:
  1.
  2.
  3. 
  
  Trigger Settings Window
  
  Multiple Protocols Analysis Simultaneously:
  Ex: I^₂C + USB PD3.0
  
  
  MSO Stack With Other Vendors of Oscilloscope:
  (*Support DSO)
  
  MSO Enables Digital & Analog Channels (Using the same channels)
  Digital & Analog Signals From MSO and External DSO From Other Vendors*BUS_SMBUS: Decode & Digital Signals   *DSO: MSO Analog Signals   *Ext DSO: External DSO Signals
  
  Add Notes & Pictures in Waveform
  Power Management Protocols Solution for MSO
  Ex: PMBus(CH0 & CH1) & The Related Power Voltage(CH2) (*Digital CH0, CH1    Analog: CH2 )
  

Protocol Analyzer (PA) Mode
It is hardware decoding, may log protocol data very long time if without waveforms.
Application timing: Preliminary protocol debug.

PA Storage Mode:
Software Main Window:

Power Sequence Verification
*This solution is only applicable to some MSO models.
*MSO2000+ series supports cascading up to 8 devices(128 CH) for power sequence measurement.

Power Sequence Report(HTML Format)